NaOH storage tanks · outfitted in Willis, TexasMon–Fri · dmiller@plasticstoragetanks.com · 936-228-1520

Guide

Sodium Hydroxide Storage Guide

How to store caustic soda safely in a plastic tank: the resin, the SG rating, freeze protection, containment, fittings and venting, in the order you’ll decide them.

Most bulk caustic is 50%Freezes near 54°F1.9 SG tankPolypropylene or HDPE

Step 1

Know Your Caustic

Write down the concentration, the coldest and warmest temperatures the tank will see, how much you need to store, and whether it’s indoors or out.

StrengthStarts to crystallize at aboutWhat it means for the tank
18%−17°F (−27°C)The lowest freezing point of any strength; freezing is rarely a concern.
25%8°F (−13°C)Freezes only in a hard cold snap; insulation may be enough.
50%54°F (12°C)Can freeze on a cool night. Suppliers advise storing it above 59°F (15°C).
73%145°F (63°C)Solid at room temperature and handled hot. Ask us before choosing a tank.

Caustic’s freezing point doesn’t simply rise with strength. Dilute solutions freeze near water’s freezing point, the lowest point is near 18%, and above that it climbs quickly, which is why the common 50% grade is also one of the easiest to freeze.

Step 2

Pick the Resin

Resin50% NaOHChoose it when
PolypropyleneA · ExcellentCaustic is stored warm or heated; continuous use up to 200°F.
Linear HDPEB · GoodCaustic is held near room temperature; the economical choice, continuous use up to 120°F.
PVDF (Kynar®)D · Not RecommendedNever for caustic: strong bases attack it.

Step 3

Choose the SG Rating

50% caustic has a specific gravity of about 1.52 to 1.54, roughly 12.7 pounds per gallon. A tank’s SG rating must be at or above the specific gravity of the liquid, so a 1.5 SG tank is not enough: order a 1.9 SG tank. Weaker blends are lighter, so tell us your strength and we’ll confirm the rating.

50% caustic is also thick, roughly 80 to 100 times as thick as water at 68°F, and thicker as it cools. Use full-size outlets and keep transfer lines short and protected from cold.

Step 4

Keep It From Freezing

▦

Insulation

Closed-cell spray foam on the sides and top slows heat loss. On its own it doesn’t add heat.

≋

Heat tracing

Pads on the tank wall under the foam, with a controller that holds temperature and alarms on high, low or lost current.

→

The lines

Insulate and trace exposed fill and transfer lines and valves, and warm unloading lines before each delivery.

A practical target: hold 50% caustic comfortably above 59°F and set the low-temperature alarm so you hear about a problem before it reaches 54°F. See insulated tanks.

Step 5

Plan Containment

Sodium hydroxide is a corrosive liquid, and fire codes based on the International Fire Code set containment rules for corrosive storage. In those codes, outdoor aboveground tanks holding more than 1,000 gallons of corrosive liquid in total need secondary containment, and indoor storage areas need spill control once a single vessel holds more than 55 gallons. Your local fire marshal and environmental regulator have the final word.

  • Double wall tank: the sealed outer tank holds a leak and keeps rain out. See HDPE and polypropylene double wall tanks.
  • Dike or basin: open containment is commonly sized for at least 120% of the largest tank, more where rain collects.

Step 6

Fittings, Gaskets and Vents

PartUseAvoid
FittingsPVC, CPVC, polypropylenePVDF
GasketsEPDM, Buna-NViton®
Metal hardware316 stainless, titaniumAluminum, zinc, tin, galvanized steel

Plastic tanks are built for atmospheric pressure only. Size the vent at least as large as the largest fill or withdrawal connection, never under 1 inch, and larger if the tank is filled from a truck with air pressure. Keep the tank closed: caustic absorbs carbon dioxide from the air, which weakens it and crusts openings. See fittings.

Before you order

Sodium Hydroxide Tank Checklist

  • Concentration, and any other chemical the tank will ever hold
  • Volume, footprint and height limits; indoors or outdoors
  • Coldest and warmest storage temperature; will you heat the tank?
  • Resin: polypropylene or HDPE, never PVDF
  • 1.9 SG rating for 50% caustic
  • Insulation and heat tracing if it can get below about 59°F
  • Containment: double wall, or a dike or basin sized for your code
  • Fittings, sizes and locations, with EPDM gaskets
  • Vent size, and how the tank will be filled

FAQ

Questions

What SG rating do I need for 50% caustic?

50% sodium hydroxide has a specific gravity of about 1.52 to 1.54, so order a 1.9 SG tank. A 1.5 SG tank is rated below the weight of the liquid.

Will my caustic freeze in this tank?

50% caustic starts to crystallize near 54°F. Outdoors or in an unheated building, choose an insulated tank with heat tracing and keep it above about 59°F.

HDPE or polypropylene for sodium hydroxide?

Both work for 50% caustic. HDPE is rated Good and costs less; polypropylene is rated Excellent and is the better choice when caustic is stored warm or heated, up to 200°F continuous.

Does a sodium hydroxide tank need containment?

Often, yes. Fire codes set containment rules for corrosive liquids, and your local fire marshal has the final word. A double wall tank, or a single wall tank in a dike or basin, meets most requirements.

Can I use a PVDF tank for caustic?

No. PVDF (Kynar®) is rated Not Recommended for sodium hydroxide because strong bases attack it. Use HDPE or polypropylene.

Is diluting caustic in the tank safe?

Mixing water into concentrated caustic releases a lot of heat. If you dilute on site, follow your supplier’s procedure and keep the tank’s temperature limit in mind: 120°F continuous for HDPE, 200°F for polypropylene.

Sources

Where These Numbers Come From

Resin, fitting, gasket and metal ratings: Bailiff chemical compatibility, sodium hydroxide (50%). Crystallization temperatures: AWWA B501 Sodium Hydroxide standard. Minimum freezing point near 18% and viscosity: Sodium Hydroxide Release Fact Sheet. Specific gravity 1.520–1.545 and storage above 59°F: supplier technical data sheets. Containment thresholds: International Fire Code, Chapter 54. Vent sizing: ASTM D 1998. Always follow your chemical supplier’s safety data sheet.

Tell Us Your Caustic Strength

Send the concentration, storage temperature, volume and fittings you need. We’ll match the resin, SG rating, insulation and gaskets and send a quote.