HDPE · Polypropylene · Double wall
Plastic tanks for caustic soda from 25 to 10,000 gallons, rated 1.9 specific gravity for 50% NaOH, with EPDM gaskets and fittings installed at our Texas plant.
Choose by concentration
Strength sets how heavy the liquid is and how easily it freezes. Most bulk caustic soda is delivered at 50%.
Used for pH control and cleaning. Lighter than 50% and slow to freeze; the lowest freezing point of any strength is near 18%. Tell us your strength and we’ll confirm the resin and SG rating.
Starts to crystallize at about 8°F, so it freezes only in a hard cold snap. Insulation alone is often enough outdoors.
Specific gravity about 1.53, so order a 1.9 SG tank. Starts to freeze near 54°F; keep it above about 59°F with insulation and heat tracing. Polypropylene is rated Excellent and HDPE Good.
Solid at room temperature and handled hot, so every resin’s temperature limit matters. Email us before choosing a tank.
Sodium hydroxide tanks
Live sizes, dimensions and prices on every page. Every tank listed is rated 1.9 SG or higher.
Linear high-density polyethylene, the economical choice for 50% caustic stored near room temperature.
View tanks →100 – 10,000 galA tank inside a sealed tank, so a leak stays contained without a separate dike.
View tanks →25 – 6,000 galRated Excellent for 50% caustic and good for continuous use up to 200°F, for caustic that’s stored warm or heated.
View tanks →Double wallThe Excellent-rated resin with built-in containment for warm caustic.
View tanks →Cone bottomDrain completely through the bottom outlet, which helps with a liquid as thick as 50% caustic.
View tanks →25 – 10,000 galSpray foam insulation with optional heat tracing pads to keep 50% caustic from freezing outdoors.
View tanks →Plan your tank
Start from a complete setup for your job, or work out the weight, SG rating, pad load and size you need.
Containment
Sodium hydroxide is a corrosive liquid, and fire codes often require secondary containment for it. A double wall tank’s sealed outer tank holds a leak from the inner tank and keeps rain and debris out.
Know your caustic
Caustic soda is heavy, thick and strongly alkaline. At 50% it weighs about half again as much as water and starts to freeze on a cool night.
It attacks aluminum, zinc, tin and galvanized steel, so we build caustic tanks in plastic and match every fitting and gasket to it. Diluting it releases a lot of heat, and an open tank absorbs carbon dioxide from the air, which weakens the solution and leaves a crust around openings. Read the sodium hydroxide storage guide to choose the resin, SG rating, freeze protection and containment for your tank.
Data: PubChem CID 14798
Fittings & gaskets
A tank is only as good as its weakest fitting. We install fittings at our plant so the tank arrives ready to plumb in.
Who stores sodium hydroxide
Sodium hydroxide is one of the most widely used industrial chemicals. These are the jobs our caustic tanks do most.
pH and alkalinity adjustment at treatment plants.
Clean-in-place (CIP) cleaning of tanks and lines.
Pulping and bleaching chemistry.
Saponification and cleaner blending.
Neutralizing acids and scrubbing gases.
Degreasing, etching and alumina refining.
FAQ
For 50% caustic stored near room temperature, a linear HDPE tank rated 1.9 SG is the economical choice. Polypropylene is rated Excellent and handles caustic stored warm or heated. Avoid PVDF (Kynar®) tanks, which strong bases attack.
50% sodium hydroxide has a specific gravity of about 1.52 to 1.54, more than a 1.5 SG tank is rated for, so order a 1.9 SG tank. Weaker blends are lighter; tell us your strength and we’ll confirm the rating.
It starts to crystallize at about 54°F (12°C), and suppliers advise storing it above about 59°F (15°C). Outdoor tanks usually need insulation and heat tracing, and exposed lines need heat too.
EPDM and Buna-N are rated Excellent. Don’t use Viton®, which is rated Not Recommended for caustic.
Often, yes. Fire codes based on the International Fire Code set containment rules for corrosive liquids, and your local fire marshal has the final word. A double wall tank, or a single wall tank in a dike or basin, meets most requirements.
Yes. We mold and outfit tanks at our plant in Willis, Texas and ship them with fittings installed. Email dmiller@plasticstoragetanks.com for freight and lead time.
Send the concentration, storage temperature, volume and fittings you need. We’ll match the resin, SG rating, insulation and gaskets and send a quote.